REDUNDANT FLIGHT CONTROL · CALGARY, ALBERTA

Redundant flight control for uncrewed aircraft, from Canada.

Two identical lanes with hardware arbitration between them, and heading from precise magnetics as well as GNSS.

We are building it from the sensors up. The AGS-M1 magnetometer board is built and field-tested, the AGS-G1 GNSS module is in design, and the flight control lanes come next. We are starting them by looking for an autopilot partner.

THE SYSTEM
IN DESIGN

Two lanes, and everything they share.

Two identical flight control lanes run side by side. The nodes both lanes need sit on both lanes' buses, with a guarded port for each, so a fault in one lane or on one bus is meant to stay there. It is in design, and nothing has flown.

THE FLIGHT CONTROL SYSTEM →
TWO LANES

Two identical flight control lanes. One commands and the other stands by. A lane that fails takes itself out of command in hardware, and the other takes over.

HEADING FROM MAGNETICS

Fluxgate magnetometers, mounted away from the aircraft's own currents and read the way the AGS-M1 reads them, give a heading that needs neither GNSS nor a radio link.

HEADING FROM GNSS

A pair of AGS-G1 modules gives a second, independent heading, and each lane checks one source against the other. The GNSS heading needs both modules; without it, the lanes use magnetic heading.

THE LANE DECIDES

Each lane checks every heading it is given and falls back on its own. The companion computer never switches a lane's heading source.

We're looking for an autopilot partner.

The flight control lanes are next, and we want to build them with a team that brings flight control software of its own. Tell us about your autopilot: king@airandgravity.com

BUILT · THE MAGNETOMETER
FIELD-TESTED

AGS-M1: the first part, built and field-tested.

The magnetometer the flight control system is built around, and a product in its own right: a three-axis fluxgate magnetometer board, built to go inside your design. On our bench its acquisition chain measures 0.035 nT/√Hz, with the inputs shorted at the sensor connector and the converter at 503.8 S/s; the board page shows how it was calculated. One board sits between the fluxgate and your host. Each row says where its value comes from, and anything not yet measured or specified is marked OPEN rather than left out.

FULL SPECIFICATIONS →
The AGS-M1 Rev B board seen at an angle, component side: the eight-pin sensor connector at the left end, the six-pin host and four-pin power connectors at the right end, and a mounting hole in each corner.
REV B · 43.18 × 95.25 MM · 4 LAYERS · COMPONENT SIDE
INTERFACE · REV B
Supply 9 V nominal DESIGN
Supply range Not yet specified OPEN
Host link RS-485 half-duplex at 100,000 baud, or 3.3 V TTL serial at 921,600 baud; one link per power-up, set by a switch DESIGN
Clock pin J3 pin 5 carries the board's own 8 MHz as shipped; do not drive a clock into it on the shipping firmware DESIGN
External clock Runs from your 8 MHz master clock on J3 pin 5, and stops cleanly if it is lost, on the clock-following firmware we send on request (one board, 4 of 4 tests, July 2026) MEASURED
Recording ≈35,000 samples on board; every sample checksummed; resumable, verified readback DESIGN
Accelerometer Three-axis, on board; a coarse tilt witness DESIGN
Connectors Molex PicoBlade, 1.25 mm pitch, on the top side. J4 power, 0530470410: 1–2 DC in, 3–4 ground. J3 host link, 0530470610: 1 TTL serial TX, 2 RS-485 A, 3 RS-485 B, 4 TTL serial RX, 5 8 MHz clock (the board's own as shipped; yours with the clock-following firmware), 6 sync (no function in the shipping firmware); the serial, clock and sync pins are 3.3 V logic. J3 has no ground pin: its signal ground is J4's. J2 sensor, 0530470810: 1–3 X, Y, Z in, 4 analog return, 5 supply return, 6 +12.5 V, 7 −12.5 V, 8 self-test. DESIGN
Mounting Four non-plated Ø3.175 mm holes, each 2.667 mm in from both edges at a corner: a 37.846 × 89.916 mm rectangle, for M3 or #4 screws. Keep-outs: both faces are free of copper to Ø5.3 mm and of parts to Ø6.0 mm around each hole, and copper and parts stay at least 0.63 mm in from every edge. DESIGN
Operating temperature Not yet specified OPEN
EVIDENCE

Bench-tested and field-tested. Both on record.

The evidence log names the board and the conditions behind each milestone, and lists what is still open beside what is done.

FULL EVIDENCE LOG →
  1. Bench board accepted.
  2. Noise sweep, sensor attached.
  3. In-spec clock tree.
  4. Runs from an external 8 MHz clock.
  5. September 2026 Field test: readings checked against a reference magnetometer on site.

On the bench

MEASURED · JULY 2026

A Rev B board, tested against a written acceptance plan, with the raw data kept beside each report.

In the field

FIELD-TESTED
Where
Industrial site
When
September 2026
Test
The field at the site, checked against a reference magnetometer alongside
GATES · 7 OF 9 CLOSED ACTIVE: Datasheet AGS-DS-001 Rev A · OPEN: Noise re-run with a shielded short
IN DESIGN · THE GNSS MODULE
IN DESIGN

AGS-G1: GNSS for redundant aircraft.

A dual-port DroneCAN RTK GNSS module. For integrators of redundant UAS, and of survey aircraft that carry magnetometers.

THE AGS-G1 MODULE →
TWO ISOLATED PORTS

GNSS on two CAN FD ports. Each has its own power stage, ground and transceiver, so a fault on one bus stays on that bus, and the module runs from either port's power.

A HARDWARE TRANSMIT GUARD

A MUTE input on each port lets the autopilot on that bus silence the module's port in hardware, without relying on the module's firmware.

HEADING FROM A PAIR

Two modules, strapped base and rover in the harness, report heading over DroneCAN without a magnetometer.

LOW-MAGNETIC BY DESIGN

Designed from low-magnetic parts. Every unit will be measured on the fluxgate bench we use for the AGS-M1, and no figure is published until the first one is.

GATES · 2 OF 7 CLOSED ACTIVE: Schematic · OPEN: Layout; First units built; Magnetic signature measured; Bench thermal test
AGS-M1 INTEGRATION

Start integrating before a board arrives.

The simulator and the test vectors let your host code run before a board is on your bench. Both are working and early, and we send them on request.

INTEGRATION GUIDE →
INTERFACE CONTROL DOCUMENT

Everything your host needs, in one numbered document. In preparation.

HOST PROTOCOL

Poll and response over RS-485 or TTL serial, with CRC-32 on every frame and a fixed register map.

INSTRUMENT SIMULATOR

The board's behaviour, with fault injection, for testing your host without hardware.

OPERATOR SOFTWARE

A Windows application for live streaming, spectrum and noise analysis, and verified recordings.

How an integration starts.

There is no cart and no price list. Every integration starts with an email to the person who designed the board: king@airandgravity.com

DOCUMENTS

Three documents, none behind a form.

The interface control document is the one to start with.

ALL DOCUMENTS →
DOCUMENT TITLE REV STATUS
AGS-ICD-002 AGS-M1: interface control document A IN PREPARATION
AGS-DS-001 AGS-M1: datasheet A IN PREPARATION
AGS-OM-003 AGS-M1: operation manual A IN PREPARATION
ABOUT

Our own designs, direct to the people who integrate them.

Air & Gravity Systems is a Canadian company. We design and build magnetic field measurement hardware, and we are designing the GNSS module and the redundant flight control system that fly with it.

Nothing here is claimed above its evidence.

NO WEAPONS · NO PAYLOAD RELEASE

We do not build weapons or anything that drops a payload.